国产a免费观看-国产a免费一级视频-国产a区-国产a视频-国产a视频精品免费观看-国产a天天免费观看美女

Welcome to the official website of Xingtai Degang Electronics Co., Ltd!
邢臺德港電子有限公司
keywords:
news information INDEX > news information > News Center > 

Time:2018.06.16     News sources: Hebei Chaoda Sealing Products Co., Ltd
When CALSPE is displayed, if the [5] button is pressed, it will enter the calibration and show that CAL000 indicates zero calibration. After confirming the empty scale and stabilizing the lamp, press the [5] key to complete the zero calibration. Display CAL001 prompts the user to start the calibration of the load point. At this point, the user enters the weighing value of the known load. (input method: press the [1] key number to change from 0-9, when the required number is pressed, press the [2] key to move the digit forward. When the load is put on and the stable light is on, press the [5] key. If the weighing value is in the normal range, the CAL002 will be displayed. At this point, press the [4] key to complete linear calibration. If nonlinear calibration is needed, the load point two will be calibrated by the same method as the load point. Similarly, the calibration of the load point three can also be carried out. But in addition to zero, there are only 3 load points to be calibrated. After the load point three is calibrated, the [5] key is pressed, and the input weighing value is normal or at any time in the calibration process the user presses the [4] key. The program will exit the calibration process and enter the weighing state.

Parameter setting

When displaying SEt---, if you press the [5] key, enter the parameter settings, showing that the XXX in D XXX represents the current dividing value. According to the [2] key, the graduation value is between 0.1, 0.2, 0.5, 1, 2, 5, 10, 20, 50, 0.1. When switching to the required dividing value, press the [5] key to complete the setting of the new dividing value and transfer it to the setting of the filtering mode. Display FiLt X, when X=0 is used, stable filtering is used. When X=1 is used, the fast reaction filter is used. It can switch between the two filtering modes by pressing the [2] key. When switching to the required filtering mode, press [5] button to complete the setting of filtering mode. And turn to the range setting to display rxxxxx. Xxxxx is the current range value. Press the [2] key to switch the range between 600100015002000300 and 500010000150002000 300005000060000. When switching to the required range, according to the [5] key, you can complete the setting of the new range value and enter the setting of the opening zero range, showing the SEtxxx, the current opening zero range in the XXX. Press the [2] key, then turn on the zero range to switch between 025102050100. These values represent a percentage range. According to the [5] key, you can complete the setting of the new boot zero range, and turn it into the accumulative setting. It shows Aut - x, x=0 represents non - automatic accumulation, and x=1 represents automatic accumulation. According to the [2] key, you can make an accumulation mode switch selection, press the [5] key to complete the new accumulation mode settings, and transfer to zero tracking settings. When zero tracking is set, L0 x is displayed, where x is the different speed of zero tracking. When x is 0, the zero point tracking is closed. When x is 1, it indicates slow zero tracking. When x is 2, it indicates medium speed zero tracking. When x is 3, it indicates fast zero tracking. You can switch between the above 4 ways by pressing the [2] key. When switching to the required way, press the [5] key to complete the setting of zero tracking and transfer time settings. When time is set, ttxxxx is displayed, where XXXX is the minute and second when the entry time is set. With the [1] key and the [2] key, you can enter the new 6 bit time (time, minutes and seconds) and press the [5] key. If the time of the input is valid value, you can complete the new time settings. Returns the function switch state.

  • PREV:
  • NEXT:
≡  contacts:Manager Wang ≡  mobile:13930926376 ≡  Telephone:0319-2158243 ≡  fax:0319-2159641 ≡  address:No. 1 in Rongtai science and Technology Incubation Park, south of Xingda street, Xingtai Economic Development Zone
河北超達密封
版權所有:邢臺德港電子有限公司       網站備案/許可證號:       

冀公網安備 13050902000085號

技術支持:邢臺市網商軟件開發有限公司
主站蜘蛛池模板: 国产动漫同人一区二区 | 99久久九九社区精 | 18禁美女裸体网站无遮挡 | 国产精品制服丝袜美 | 国产三级精品三级 | 国产精品丝袜熟女 | 91精品国产午夜福利在线观看 | 国产免费一区二区视频麻豆 | 国产成人av大片大片在线播 | 国产精品无码久久四虎 | 国产产精品亚洲一区二区在线观看 | 国产白丝jk制服在线视频 | 国产成人精品一区二区三区不卡 | 成人免费无码大片a毛片抽搐色欲 | 高清女同学巨大乳在线 | 精品国产成人一区二区99 | av免费网址在线观看 | 国产99久久久国产精品免 | 成年做羞羞的视频网 | 精品国产亚一区二区三区不卡 | 国产精品三级av及在线观看 | 国产美女自慰喷水 | 国产精品亚洲欧美动漫 | 91精品国产免费久久久久久 | 精品亚洲一区二区在线播 | 成人无码一区二区三区 | 国产人妻精品 | 99久久久国产精品免费软件 | 国产成人精品免费青青草原 | 国产白领诱惑在线观看 | 国产精品白嫩美女在线观看app | 国产亚洲欧洲人人网在线观看 | 国产在线视频主播区 | 精品一级毛片a久久久久 | 国产精品初高中精品免费观看 | 国产极品粉嫩的馒头一线天 | 国产aⅴ精品一区二区三区 国产aⅴ精品一区二区三区久 | 国产av夜夜欢一区二区 | 国产欧美动漫 | 国产亚洲欧美精品久久久 | 国产精品高清网站 |